manualshive.com logo in svg

Cisco ASR 900 Series, Руководство пользователя, Страница: 142 / 310

Поделиться
Скачать
Cisco ASR 900 Series Скачать руководство пользователя страница 142

 

54

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter  

  Caveats in Cisco IOS XE 3.7S Releases

  •

CSCuc44394

Symptom:

 The router stops passing MLPPP traffic after a Stateful Switchover (SSO). 

Conditions:

 Occurs when you perform an SSO with a TDM interface module. 

Workaround:

 There is no workaround. 

Resolved Caveats—Cisco IOS XE Release 3.7(1)aS

This section documents the issues that have been resolved in Cisco IOS XE Release 3.7(1)aS.

  •

CSCty63969

Symptoms:

 Ping fails to remote MEPs.

Conditions:

 Occurs when you configure CFM and ping RMEPs with a packet size of greater than 

1478 bytes.

Workaround:

 There is no workaround.

  •

CSCua02058

Symptoms:

 When you configure the OC-3 interface module, only 1000 of 1008 interfaces are 

configurable on the router; of the 1000 interfaces, only 957 become active.

Conditions:

 Occurs when you configure interfaces on the OC-3 interface module.

Workaround:

 There is no workaround.

  •

CSCua51772

Symptoms:

 The router does not display PID or DOM values.

Conditions:

 Occurs with the following SFPs:

  –

ONS-SI-155-L2

  –

ONS-SI-155-L1

  –

ONS-SI-155-I1

Workaround:

 There is no workaround. 

  •

CSCua55122

Symptoms:

 The OC-3 interface module crashes when you create a high number of ATM IMA 

interfaces.

Conditions:

 Occurs when you configure multiple ATM IMA interfaces with fewer than 16 links per 

bundle.

Workaround:

 Perform a hard OIR on the interface module. 

  •

CSCua87805

Symptoms:

 The OC-3 interface module goes into an Out Of Service state. 

Conditions:

 The issue can occur during bootup or OIR of the OC-3 interface module. 

Workaround:

 Perform an OIR on the OC-3 interface module. 

  •

CSCua93803

Symptoms: 

The 

boot system flash

 command displays unexpected behavior.

Conditions: 

Occurs when you use the 

boot system flash

 command in either of the following 

formats:

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов