manualshive.com logo in svg

Cisco ASR 900 Series, Руководство пользователя, Страница: 111 / 310

Поделиться
Скачать
Cisco ASR 900 Series Скачать руководство пользователя страница 111

 

23

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter 

  Caveats in Cisco IOS XE 3.7S Releases

  •

CSCuf07508

Symptom:

 The Gigabit Ethernet port on interface module does not come up after a reload. 

Conditions:

 This issue occurs when the Cisco ASR 903 router is reloaded multiple times.

Workaround:

 Perform an OIR of the interface module.

  •

CSCuf79397

Symptom: 

The F1 interface is stuck in init state after OIR of the standby RSP or standby reload.

Conditions:

 This issue occurs after the standby RSP is reloaded or OIR is performed.

Workaround:

 There is no workaround.

  •

CSCub94462

Symptom:

 The router displays object download error messages on the console similar to the 

following example:

%FMFP-3-OBJ_DWNLD_TO_CPP_FAILED"

Conditions:

 Occurs when you take the following actions:

  –

Apply the 

mac address sticky

 command

  –

Configure 25 incremental MAC addresses

  –

Apply the 

clear mac-address-table bdomain

 command

  –

Remove a 

mac security sticky

 configuration from an EVC interface

Workaround: 

Do not issue 

clear mac-address-table

 command when the 

mac security sticky

 is 

configured.

  •

CSCue51682

Symptom:

 The REP protocol flaps, as indicated by the following error messages: 

*Feb  8 06:51:38.857: %REP-4-LINKSTATUS: GigabitEthernet0/0/1 (segment 10) is 

non-operational due to neighbor not responding

*Feb  8 06:51:39.096: %REP-4-LINKSTATUS: GigabitEthernet0/0/1 (segment 10) is 

operational

Conditions:

 Occurs under the following conditions:

  –

The router is sending traffic using the incremental MAC address table

  –

Fast LSL is configured using a 200ms timer.

  –

The router is configured with more than 2000 MAC addresses.

Workaround:

 Remove fast LSL from the REP configuration.

  •

CSCuf86247

Symptom:

 SNMP MIB variables related to BDI counters do not function properly.

Conditions:

 Occurs when you use SNMP MIB variables related to BDI interface counters.

Workaround:

 There is no workaround.

  •

CSCug05491

Symptom:

 The router drops traffic on VPLS circuits.

Conditions:

 Occurs when you take the following actions:

  –

Configure REP with VLAN load balancing

  –

Configure VPLS VFI on the VLANs

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов