Cisco ASR 900 Series Скачать руководство пользователя страница 182

Страница: 182 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.8S Releases

Workaround:

There is no workaround. However, the issue does not have any functionality impact

on the system.

•

CSCud26240

Symptom:

The router displays Nile mgrs leak error messages.

Conditions:

Occurs when you configure L3VPN and L2VPN services at a high scale.

Workaround:

There is no workaround.

•

CSCud26382

Symptom:

The router drops traffic on an EFP interface after you perform a stateful switchover

(SSO).

Conditions:

Occurs under the following conditions:

–

You boot the standby RSP

–

The router configuration contains an EFP interface on a Gigabit Ethernet port and a bridge
domain interface in a down state.

–

After the router reaches an SSO state, you issue a no shutdown command on the peer router to
bring the EFP interface up.

–

You perform an stateful switchover (SSO) on the router.

Workaround:

Issue a shutdown/no shutdown on the gigabit Ethernet port.

•

CSCud28553

Symptom:

The router stops passing Switch Port Analyzer (SPAN) traffic.

Conditions:

Occurs after you apply a

shutdown

no shutdown

on the SPAN source port with

Ethernet flow point (EFP) and bridge domain interface (BDI) configurations.

Workaround:

Enable and disable the SPAN session

•

CSCud28685

Symptom:

Ping fails between the CE1 and CE2 devices when the ASR 903 is acting as the PE

device.

Conditions:

Occurs when the SONET controller or ATM interface experiences an interface flap.

Workaround:

Perform a soft OIR on the interface module.

•

CSCud28787

Symptom:

The 10 gigabit Ethernet interface module (IM- A900-IMA1X ) flaps.

Conditions:

Occurs when the IM passes high traffic volumes for an extended period of time.

Workaround:

There is no workaround.

•

CSCud31852

Symptom:

The router displays traffic polarization with L3VPN traffic.

Conditions:

Occurs under the following conditions:

–

The P router has multiple ECMP paths

–

The ECMP paths are port-channels

Traffic is distributed between ECMP paths, but polarization occurs on the port-channel member
links.

Workaround:

There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 182 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: