manualshive.com logo in svg

Cisco ASR 900 Series, Руководство пользователя, Страница: 279 / 310

Поделиться
Скачать
Cisco ASR 900 Series Скачать руководство пользователя страница 279

 

25

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

•

CSCue07040

Symptom: 

The router continuously displays ESDHC and MMCBLK0 errors.

Conditions: 

This issue is observed when the SD flash memory is being accessed.

Workaround: 

There is no workaround. Replace or format the bootflash. 

•

CSCue14054

Symptom: 

When a port joins more number of multicast groups at a time, traffic drops for a few 

groups.

Conditions: 

This issue is observed when a port joins more than 900 multicast groups.

Workaround: 

Use the 

shutdown

 and 

no shutdown

 commands on that interface.

•

CSCue17123

Symptom: 

ATM and IMA pings fail from the second interface after performing an SSO.

Conditions: 

This issue is observed when you have multiple ATM interfaces and perform a 

switchover. 

Workaround: 

There is no workaround. 

•

CSCue18997

Symptom:

 In unicast mode, the PTP slave stream does not lock to the PTP master.

Conditions:

 This issue id observed after the PTP master configuration is removed and reconfigured.

Workaround:

 There is no workaround.

•

CSCue25146

Symptom: 

When the controller in active machine flaps, the standby machine is reloaded. 

Conditions: 

This issue is observed when you configure ATM and the controller, use 

shutdown

 and 

no shutdown 

commands on the controller in the active machine.

Workaround: 

There is no workaround 

•

CSCue27652

Symptoms: 

The ATM interfaces are deleted while performing an SSO.

Conditions: 

This issue is observed when the ATM interfaces are deleted on the standby machine 

after performing an IM OIR.

Workaround: 

There is no workaround. 

•

CSCue30481

Symptom: 

The router does not lock to the syncE clock source after a reload. It is in Ql-failed state.

Conditions:

 This issue is observed when you reload the router with a saved syncE configuration.

Workaround: 

Delete and reconfigure the clock source.

•

CSCue35295

Symptom: 

Traffic drops when you remove the BFD template.

Conditions:

 This issue is observed when you remove the BFD template from the global 

configuration.

Workaround: 

There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов