Broadcom Brocade G720 Скачать руководство пользователя страница 7

Страница: 7 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Introduction

About This Document

This hardware installation guide contains procedures and safety requirements for installing the Brocade G720 Switch

into a rack system or as a stand-alone device. Also provided are steps to initially configure the switch for operation, verify

and monitor operation, replace switch field-replaceable units (FRUs), and install transceivers and cables. Complete

technical specifications for the switch are also included.

Supported Hardware and Software

The Brocade G720 Switch is introduced in the Fabric OS

9.0.0 release. The following tables list the power supply and

fan assemblies and the rack mount kits supported on this device.

Table 1: Power Supply and Fan Assemblies

Part Number

Description

Introduced (OS)

Currently Supported (OS)

XBR-G350WPSAC-F

350W AC power supply with nonport-side

exhaust airflow

Fabric OS 9.0.0

Fabric OS 9.x

XBR-G350WPSAC-R

350W AC power supply with nonport-side

intake airflow

Fabric OS 9.0.0

Fabric OS 9.x

NOTE

Fabric OS 9.x refers to any supported release within the 9.x generation of Fabric OS.

Table 2: Rack Mount Kits

Part Number

Description

XBR-R000294

Universal two-post mid-mount or flush-mount rack kit

XBR-R000296

Universal four-post fixed rack mount kit

The Brocade G720 Switch requires optics that are labeled with an SEC designation.
The following image provides an example of an optic label with SEC in the description (32G LW-SEC 10km).

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды