Broadcom Brocade G720 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 86

background image

G720-Install-IG101 Installation Guide

Brocade

®

G720 Switch Hardware Installation Guide

LS Attributes: [FID: 1, Base Switch: No, Default Switch: No, Ficon Switch: No, Address Mode 0]
Index Port Address Media Speed State Proto
==================================================
0 0 9c0000 id N64 Online FC F-Port 10:00:00:10:9b:8f:2d:1c
1 1 9c0100 id N64 Online FC F-Port 10:00:00:10:9b:8f:2d:1b
2 2 9c0200 id N64 Online FC F-Port 10:00:00:10:9b:8f:2d:e8
3 3 9c0300 id N64 Online FC F-Port 10:00:00:10:9b:8f:2d:e7
4 4 9c0400 id N64 Online FC F-Port 10:00:00:10:9b:8f:2c:e2
5 5 9c0500 id N64 Online FC F-Port 10:00:00:10:9b:8f:2c:e1
6 6 9c0600 id N64 Online FC F-Port 10:00:00:10:9b:8c:54:69
7 7 9c0700 id N64 Online FC F-Port 10:00:00:10:9b:8c:54:6a
(output truncated)

The

tempshow

command shows the current temperature of the EM sensors.

switch:admin> tempshow
Sensor ID|Sensor Index|State |Centigrade |Fahrenheit |
-------------------------------------------------------------
1 |0 |Ok |30 |86 |
2 |1 |Ok |34 |93 |
3 |2 |Ok |29 |84 |
4 |3 |Ok |30 |86 |
5 |4 |Ok |30 |86 |
6 |5 |Ok |32 |89 |
7 |6 |Ok |29 |84 |
8 |7 |Ok |36 |96 |
9 |8 |Ok |39 |102 |
10 |9 |Ok |28 |82 |
11 |10 |Ok |30 |86 |
12 |11 |Ok |N/A |N/A |
13 |12 |Ok |43 |109 |

Backing Up the Configuration

Back up the configuration regularly to ensure that a complete configuration is available for downloading to a replacement

switch. Perform the following steps:
1. Log on to the device as the admin user.
2. Back up the device configuration to an FTP server by entering the

configUpload

command as shown in the

following example.

E_146155_C5c:FID128:admin> configupload
Protocol (scp, ftp, sftp, local) [ftp]:
Server Name or IP Address [host]: 192.0.2.0
User Name [user]: anonymous
Path/Filename [(home dir>/config.txt]: home/dumps/config.fid100.txt
Section (all|chassis|FID# [all]):

configUpload complete: All selected config parameters are uploaded
2020/03/05-23:57:59, [CONF-1001], 130, FID 128, INFO, E_146155_C5c, configUpload completed successfully
for all.

G720-Install-IG101

52

Broadcom

«
...
50
51
52
53
54
...
»

Содержание Brocade G720























































































Отзывы:

Нет отзывов

Похожие инструкции для Brocade G720

Бренд: ABB Страницы: 7

Бренд: H3C Страницы: 38

Бренд: H3C Страницы: 36

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 36

S12500X-AF Series

Бренд: H3C Страницы: 21

S12500X-AF Series

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 16

Бренд: H-Tronic Страницы: 32

Бренд: Yeastar Technology Страницы: 11

SMALL OFFICE CyberSwitch 150

Бренд: Cabletron Systems Страницы: 106

Бренд: Zektor Страницы: 84

EdgeSwitch 10 XP

Бренд: Ubiquiti Страницы: 13

Бренд: Datavideo Страницы: 38

Бренд: TRENDnet Страницы: 11

Бренд: Dahua Страницы: 15

Бренд: Comtrend Corporation Страницы: 2

Бренд: A-Neuvideo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды