Broadcom Brocade G720 Скачать руководство пользователя страница 10

Страница: 10 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

–

48 LEDs (green/amber) for the first 48 SFP+ ports and 8 LEDs (green/amber/white) for the last 8 SFP+ ports.

–

One green LED to indicate valid system power.

–

One bicolor (green/amber) LED to indicate the system status.

–

Two Ethernet LEDs: one green LED to indicate link speed of 1000/100/10Mb/s and one green LED to indicate

activity.

•

SEEPROM for switch identification.

•

Encryptable SEEPROM.

•

Secure encryptable SEEPROM.

NOTE

The License ID is protected by the secure encryptable SEEPROM.

•

Secure boot.

•

Real-time power monitoring.

•

Real-time voltage monitoring.

•

Real-time fan monitoring including airflow direction.

•

Real-time digital thermometers for temperature monitoring.

•

Real-time clock (RTC) with battery.

License Options

The Brocade G720 Switch uses a capacity-based Ports on Demand (POD) license method. Refer to the

Brocade Fabric

OS Software Licensing Guide

for more details.

Port-Side View of the Device

The following illustration shows the port-side view of the Brocade G720 Fibre Channel switch.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды