Broadcom Brocade G720 Скачать руководство пользователя страница 28

Страница: 28 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

CAUTION

The device must be turned off and disconnected from the fabric during this procedure.

NOTE

The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 2U

device. The illustrations in the rack installation procedures are for reference only and may not show the actual

device.

Complete the following tasks to install the device in a four-post rack:
1.

Attaching the Front Brackets to the Rear of the Device

Attaching the Extensions to the Front of the Device

Installing the Device in the Rack

Attaching the Rear Brackets to the Extensions at the Front of the Device

Attaching the Rear Brackets to the Front Rack Posts

Attaching the Front Brackets to the Rear of the Device

NOTE

In this installation, the brackets are named as listed in the parts list even though the installation of the brackets is

reversed from the flush-front installation.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды