Broadcom Brocade G720 Скачать руководство пользователя страница 83

Страница: 83 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

DANGER

Make sure that the power source circuits are properly grounded, and then use the power cord supplied with the

device to connect it to the power source.

GEFAHR

Stellen Sie sicher, dass die Stromkreise ordnungsgemäß geerdet sind. Benutzen Sie dann das mit dem Gerät

gelieferte Stromkabel, um es an die Srromquelle anzuschließen.

DANGER

Vérifiez que les circuits de sources d'alimentation sont bien mis à la terre, puis utilisez lecordon d'alimentation

fourni avec le dispositif pour le connecter à la source d'alimentation.

PELIGRO

Verifique que circuitos de la fuente de corriente están conectados a tierra correctamente; luego use el cordón

de potencia suministrado con el instrumento para conectarlo a la fuente de corriente

DANGER

Remove both power cords before servicing.

GEFAHR

Trennen Sie beide Netzkabel, bevor Sie Wartungsarbeiten durchführen.

DANGER

Retirez les deux cordons d'alimentation avant toute maintenance.

PELIGRO

Desconecte ambos cables de alimentación antes de realizar reparaciones.

DANGER

Disconnect the power cord from all power sources to completely remove power from the device.

GEFAHR

Ziehen Sie das Stromkabel aus allen Stromquellen, um sicherzustellen, dass dem Gerät kein Strom zugeführt

wird.

DANGER

Débranchez le cordon d'alimentation de toutes les sources d'alimentation pour couper complètement

l'alimentation du dispositif.

PELIGRO

Para desconectar completamente la corriente del instrumento, desconecte el cordón de corriente de todas las

fuentes de corriente.

DANGER

To avoid high voltage shock, do not open the device while the power is on.

GEFAHR

Das eingeschaltete Gerät darf nicht geöffnet werden, da andernfalls das Risiko eines Stromschlags mit

Hochspannung besteht.

DANGER

Afin d'éviter tout choc électrique, n'ouvrez pas l'appareil lorsqu'il est sous tension.

PELIGRO

Para evitar una descarga de alto voltaje, no abra el dispositivo mientras esté encendido.

DANGER

Batteries used for RTC/NVRAM backup are not located in operator-access areas. There is a risk of explosion

if a battery is replaced by an incorrect type. Dispose of used components with batteries according to local

ordinance and regulations.

GEFAHR

Die für die RTC/NVRAM-Sicherung verwendeten Batterien, befinden sich nicht in für den Bediener

zugänglichen Bereichen. Bei Ersetzen der Batterie durch einen falschen Typ besteht Explosionsgefahr.

Entsorgen Sie gebrauchte Komponenten mit Batterien gemäß den lokalen Auflagen und Vorschriften.

DANGER

Les batteries utilisées pour la sauvegarde de l'horloge et de la mémoire ne sont pas remplaçables par

l'opérateur. Il y a risque d'explosion si la batterie est remplacée par une d'un type incompatible. Jetez/recyclez

les batteries conformément aux normes locales.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды