Broadcom Brocade G720 Скачать руководство пользователя страница 27

Страница: 27 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Attaching the Rear Brackets to the Rack Posts

Complete the following steps to attach the rear brackets to the rack posts.
1. Attach the right rear bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts,

as shown in the figure. Use the upper and lower holes in the bracket.

2. Attach the left rear bracket to the left rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts.

Use the upper and lower holes in the bracket.

3. Tighten all 10-32 x 5/8-in. screws to a torque of 29 cm-kg (25 in.-lb).

Figure 8: Attaching the Rear Brackets to the Rack Posts

1. Screws, 10-32 x 5/8-in. Panhead Phillips

2. Retainer Nuts, 10-32

Flush-Rear (Recessed) Mounting

Flush-rear (recessed) mounting is similar to flush-front mounting except that the brackets are reversed on the device.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды