Broadcom Brocade G720 Скачать руководство пользователя страница 70

Страница: 70 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Brocade G720 Switch Technical Specifications

The following tables highlight the features and specifications for the Brocade G720 Switch.

System Specifications

System Component

Description

Enclosure

1U, port-side back-to-front exhaust airflow, power from the back.

Power inlet

C14.

Power supplies

Dual, hot-swappable, redundant, AC input power supplies with integrated system cooling fans. DC

power supplies are not supported on the Brocade G720 Switch.

Fans

Fans are integrated into each power supply and fan assembly.

Cooling

Port side to the nonport side of the switch (nonport-side exhaust) and nonport side to the port side

(port-side exhaust).

System architecture

Nonblocking shared memory switch.

Fibre Channel Ports

System Component

Description

Fibre Channel ports

56 SFP+ ports that support any combination of short wavelength (SWL) and long wavelength (LWL)

optical media.

Each of the 56 SFP+ ports supports 8, 10, 16, 32, and 64Gb/s Fibre Channel speeds.

The SFP+ ports are capable of autonegotiating to 8, 16, 32, or 64Gb/s speeds depending on the

SFP+ model and the minimum supported speed of the optical transceiver at the other end of the link.

•

A 64Gb/s optical transceiver can autonegotiate to 64Gb/s, 32Gb/s, or 16Gb/s.

•

A 32Gb/s optical transceiver can autonegotiate to 32Gb/s, 16Gb/s, or 8Gb/s.

•

A 10Gb/s optical transceiver can autonegotiate to 10Gb/s.

ANSI Fibre Channel protocol

FC-PH (Fibre Channel Physical and Signaling Interface standard).

Modes of operation

Fibre Channel Class 2 and Class 3.

Fabric initialization

Complies with FC-SW-3 Rev. 6.6.

Fibre Channel over IP (FCIP)

Complies with FC-IP 2.3 of the FCA profile.

Port status

48 LEDs (green/amber) for the first 48 SFP+ ports and 8 tri-color LEDs (green/amber/white) for the

last 8 SFP+ ports: 48, 50, 52, 54, 56, 58, 60, and 62. The last set of LEDs pulse once in white before

indicating the FC port status in green or amber. All functionalities pertaining to the green/amber

colors for the last 8 LEDs remain the same as the first 48 LEDs.

Other Ports

System Component

Description

Serial console port

UART mini-USB.

Ethernet management port

One 100/1000Mb/s Ethernet port.

USB port

One external USB port.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды