Broadcom Brocade G720 Скачать руководство пользователя страница 16

Страница: 16 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Table 4: Facility Requirements

Type

Requirements

Electrical

•

Adequate supply circuit, line fusing, and wire size, as specified by the electrical rating on the

switch nameplate.

•

Circuit protected by a circuit breaker and grounded in accordance with local electrical codes.

See the technical specifications at the end of this guide for complete power supply specifications.

Thermal

•

A Maximum airflow of 170 cubic meters/hour (100 cubic ft/min.) available in the immediate

vicinity of the switch. Minimal would be 120 cubic meters/hour (71 cubic ft/min). Although

this airflow may exceed the airflow maximum listed in the device technical specifications, the

additional airflow is recommended to pressurize the inlet (cool isle) side of rack installations

relative to the exhaust side to minimize recirculation of hot air back to the inlet side.

•

Ambient air temperature not exceeding 40°C (104°F) while the switch is operating.

Rack (when rack-mounted)

•

One rack unit (1U) in a 48.3 cm (19 in.) rack.

•

All equipment in the rack grounded through a reliable branch circuit connection.

•

Additional weight of the switch not to exceed the rack’s weight limits.

•

Rack secured to ensure stability in case of unexpected movement.

Quick Installation Checklist

The following checklists provide a high-level overview of the basic installation process from the planning stage to the point

where the device comes online and is ready to be deployed. Completing all the tasks in the suggested order ensures

successful installation. Print these checklists and take them to the installation site.

Preinstallation Tasks

Review all installation requirements ahead of time as part of your site preparation. Careful planning and site preparation

ensures seamless installation, especially when installing multiple devices.

Table 5: Installation Prerequisites

Task

Task Details or Additional Information

Completed

Unpack the device.

Take an inventory of the hardware components included in your shipment. See

Shipping Carton Contents

Gather necessary components and

required tools.

Review the time and items required at the beginning of each chapter to ensure

that you have gathered all necessary components that are required for the

following installation tasks:

•

Mounting the Device

•

Installing Transceivers and Cables

•

Power Supply and Fan Assembly

Review the safety precautions.

See

Safety Precautions

. For translations, see

Cautions and Danger Notices

the end of this guide.

Plan the installation.

Decide whether you want to install the unit on a flat surface or in a rack. For

rack installation, obtain the appropriate rack mount kit. See

Mounting Options

Review and verify installation

requirements.

Verify that the following requirements are met. See

Facility Requirements

•

Power requirements

•

Environmental requirements

•

Clearance for stand-alone or rack installation

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды