Broadcom Brocade G720 Скачать руководство пользователя страница 84

Страница: 84 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

PELIGRO

Las baterías usadas para respaldo de RTC/NVRAM no se encuentran en areas de acceso del operador. Existe

riesgo de explosión si una batería es remplazada por un tipo incorrecto. Deshágase de los componentes

usados con las baterías según las politicas y regulaciones locales.

Dangers Related to Equipment Weight

DANGER

Make sure the rack housing the device is adequately secured to prevent it from becoming unstable or falling

over.

GEFAHR

Stellen Sie sicher, dass das Gestell für die Unterbringung des Geräts auf angemessene Weise gesichert ist, so

dass das Gestell oder der Schrank nicht wackeln oder umfallen kann.

DANGER

Vérifiez que le bâti abritant le dispositif est bien fixé afin qu'il ne devienne pas instable ou qu'il ne risque pas de

tomber.

PELIGRO

Verifique que el bastidor que alberga el instrumento está asegurado correctamente para evitar que pueda

hacerse inestable o que caiga.

Laser Dangers

DANGER

All fiber-optic interfaces use Class 1 lasers.

GEFAHR

Alle Glasfaser-Schnittstellen verwenden Laser der Klasse 1.

DANGER

Toutes les interfaces en fibre optique utilisent des lasers de classe 1.

PELIGRO

Todas las interfaces de fibra óptica utilizan láser de clase 1.

DANGER

Use only optical transceivers that are qualified by Broadcom and comply with the FDA Class 1 radiation

performance requirements defined in 21 CFR Subchapter I, and with IEC 60825 and EN60825. Optical products

that do not comply with these standards might emit light that is hazardous to the eyes.

GEFAHR

Verwenden Sie nur optische Transceiver, die von Broadcom und die die Anforderungen gemäß FDA Class

1 Radiation Performance Standards in 21 CFR, Unterkapitel I, sowie IEC 60825 und EN60825 erfüllen.

Optische Produkte, die diese Normen nicht erfüllen, können Strahlen aussenden, die für das menschliche Auge

gefährlich sind.

DANGER

Utilisez uniquement des émetteurs-récepteurs optiques certifiés par Broadcom et conformes aux exigences

sur la puissance de rayonnement de catégorie 1 de la FDA définies au sous-chapitre 21 CFR I et à les normes

IEC 60825 et EN60825. Les produits optiques non-conformes à ces normes sont susceptibles d’émettre une

lumière dangereuse pour les yeux.

PELIGRO

Utilice sólo transceptores ópticos aprobados por Broadcom y que cumplan con las normas IEC 60825 y

EN60825, y con los estándares de rendimiento Clase 1 de FDA definidos en el subcapítulo I de 21 CFR. Los

productos ópticos que no cumplan con estos estándares pueden emitir luz dañina para los ojos.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды