Broadcom Brocade G720 Скачать руководство пользователя страница 22

Страница: 22 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

2. Extension Brackets, Medium (2)

3. Rear Brackets, Short (2)

4. Rear Brackets, Long (2)

5. Bracket Extensions, Long (2)

6. Screw, 8-32 x 5/16-in. Panhead Phillips (8)

7. Screw, 8-32 x 5/16-in. Flathead Phillips (16)

8. Screw, 6-32 x 1/4-in. Panhead Phillips (8)

9. Screw, 10-32 x 5/8-in. Panhead Phillips (8)

10. Retainer Nut, 10-32 (8)
Ensure that the items listed and illustrated are included in the kit. Note that not all parts may be used with certain

installations depending on the device type.

CAUTION

Use the screws specified in the procedure. Using longer screws can damage the device.

Flush-Front Mounting

CAUTION

The device must be turned off and disconnected from the fabric during this procedure.

NOTE

The illustrations in the rack installation procedures are for reference only and may not show the device that you

are installing.

Complete the following tasks to install the device in a four-post rack.
1.

Attaching the Front Brackets

Attaching the Extension Brackets to the Device

Installing the Device in the Rack

Attaching the Rear Brackets to the Extensions

Attaching the Rear Brackets to the Rack Posts

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды