Broadcom Brocade G720 Скачать руководство пользователя страница 61

Страница: 61 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Table 12: FC Port Status LED Patterns during Normal Operation

LED Color

Status of Hardware

Recommended Action

No light

Indicates one of the following:

•

No signal or light carrier (media or

cable) detected.

•

The device may be currently initializing.

•

The connected device is configured in

an offline state.

•

Verify that the power LED is on, and

check the SFP+ and cable.

•

Verify that the device is not currently

being initialized.

•

Verify the status of the connected

device.

Steady green

The port is online (connected to an external

device) but has no traffic.

No action is required.

Slow-flashing green (on for 1 second; then

off for 1 second)

The port is online but is segmented

because of a loopback cable or

incompatible device connection.

Verify that the correct device is attached to

the switch.

Fast-flashing green (on for 1/4 second; then

off for 1/4 second)

The port is online, and an internal loopback

diagnostic test is running.

No action is required.

Flickering green

The port is online, and frames are flowing

through the port.

No action is required.

Steady amber

The port is receiving light or signal carrier,

but it is not online yet.

No action is required.

Slow-flashing amber (on for 2 seconds;

then off for 2 seconds)

The port is disabled because of diagnostics

or the

portDisable

command.

Reset the port.

The

portCfgPersistentDisable

command is persistent across reboots.

Fast-flashing amber (on for 1/2 second;

then off for 1/2 second)

The SFP+ or port is faulty.

Reset the port.

Replace the SFP+. Must be a Brocade-

branded SFP+.

Interpreting Nonport-Side LEDs

Use the following table to interpret the power supply and fan assembly status LED during normal operation.

Table 13: Power Supply and Fan Assembly Status LED Patterns during Normal Operation

LED Color

Description

Action Required

No light

The power supply and fan assembly is not receiving

power, or is off.

Verify that the power supply and fan

assembly is on and seated and that the

power cord is connected to a functioning

power source.

Steady green

The power supply and fan assembly is operating normally. No action is required.

Flashing green (for more

than 5 seconds)

The power supply and fan assembly is faulty for one of the

following reasons:

•

The assembly is switched off (flashing for ~ 5 seconds,

then off).

•

The power cable is disconnected (flashing for ~ 5

seconds, then off).

•

The power supply and fan assembly has failed.

When the device is first powered on, the power supply

and fan assembly status LED flashes until the POST has

completed.

Try one of the following:

•

Check the power cable connection.

•

Verify that the assembly is powered on.

•

Replace the power supply and fan

assembly.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды