Broadcom Brocade G720 Скачать руководство пользователя страница 35

Страница: 35 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

You can mount the device in a two-post rack in two ways:

•

With the port side flush with the front posts

•

With the posts mounted to the mid-section of the device

Observe the following when mounting this device:

•

Two people are required to install the device in a rack. One person should hold the device, while the other while the

other screws in the front and rear brackets.

•

Before mounting your device, review any specific installation and facility requirements in the hardware installation

guide for the device.

•

Hardware devices illustrated in these procedures are for reference only and may not depict the device that you are

installing into the rack.

Time and Items Required

Allow 15 to 30 minutes to complete the installation.
The following items are required to install the device using the Universal Two-Post Rack Kit:

•

No. 2 Phillips torque screwdriver

•

1/4-in. slotted-blade torque screwdriver

Parts List

The following parts are provided with the Universal Two-Post Rack Kit (XBR-R000294):

Figure 15: Universal Two-Post Rack Kit Parts

1. Front Brackets (2)

2. Rear Brackets, 5–6-in. Post (2)

3. Rear Brackets, 3–5-in. Post (2)

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды