Broadcom Brocade G720 Скачать руководство пользователя страница 38

Страница: 38 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Attaching the Front Brackets to the Rack

Complete the following steps to install the device in the rack.
1. Position the device in the rack, as shown in the figure, providing temporary support under the device until the rack kit is

fully secured to the rack.

2. Attach the right front bracket to the right rack upright using two 10-32 x 5/8-in. panhead screws and two retainer nuts.

Use the upper and lower holes in the bracket.

3. Attach the left front bracket to the left rack upright using two 10-32 x 5/8-in. panhead screws and two retainer nuts.

Use the upper and lower holes in the bracket.

4. Tighten all the 10-32 x 5/8-in. screws to a torque of 29 cm-kg (25 in.-lb).

Figure 17: Attaching the Front Brackets to the Rack

1. Screws, 10-32 x 5/8-in. Panhead Phillips

2. Retainer Nuts, 10-32

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды