Broadcom Brocade G720 Скачать руководство пользователя страница 59

Страница: 59 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Figure 27: Brocade G720 Switch Port-Side LEDs - Right Side

1. SFP+ Upper Port 48

2. SFP+ Upper Port 50

3. SFP+ Lower Port 52

4. SFP+ Lower Port 54

5. SFP+ Upper Port 56

6. SFP+ Upper Port 58

7. SFP+ Lower Port 60

8. SFP+ Lower Port 62

System Power LED

Use the following table to interpret the system power LED.

Table 9: System Power LED Patterns during Normal Operation

LED Color

Status of Hardware

Recommended Action

No light

The system is off, or there is an internal

power supply failure.

Verify that the system is powered on, that

the power cables are attached, and that

your power source is live.

If the system power LED is not green, the

unit may be faulty.

Contact your solution provider.

Steady green

The system is on, and power supplies are

functioning properly.

No action is required.

System Status LED

Use the following table to interpret the system status LED.

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды