Broadcom Brocade G720 Скачать руководство пользователя страница 12

Страница: 12 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Nonport-Side View of the Device

The following illustration shows the nonport-side view of the Brocade G720 FC switch.

Figure 2: Nonport-Side View with AC Power Supply and Fan Assembly Units

1. #6-32 for Screw Mounting of the Ground Cable

2. Ground Marking

3. Power Supply and Fan Assembly 2

4. Power Supply and Fan Assembly 1

5. Captive Screw

6. Handle

7. Power Supply and Fan Assembly Status LED

8. Power-On Switch

9. Power Supply Receptacle

Device Management Options

You can use the management functions built into the device to monitor the fabric topology, port status, physical status, and

other information to help you analyze switch performance and to accelerate system debugging. The device automatically

performs a power-on self-test (POST) each time it is turned on. A RASlog message is generated for any detected startup

errors.
You can manage the device using any of the management options that are listed in the following table.

Table 3: Management Options for the Device

Management Tool

Out-of-Band Support

Reference Documents

Command line interface (CLI)

Up to two admin sessions and four user

sessions simultaneously.

Ethernet or serial connection

Brocade Fabric OS Administration Guide

Brocade Fabric OS Command Reference Manual

Brocade EZSwitchSetup

EZSwitchSetup helps to complete the

basic configuration for single-switch setup.

Ethernet or serial connection

EZSwitchSetup Software Installation Guide

EZSwitchSetup Administrator's Guide

Brocade Web Tools

Ethernet or serial connection

Brocade Fabric OS Web Tools Administration Guide

Standard SNMP applications

Ethernet or serial connection

Brocade Fabric OS MIB Reference Manual

Management Server

Ethernet or serial connection

Brocade Fabric OS Administration Guide

Brocade Fabric OS Command Reference Manual

Brocade SANnav Management Portal

must be purchased separately.

Ethernet or serial connection

Brocade SANnav documentation set

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды