Broadcom Brocade G720 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 86

background image

G720-Install-IG101 Installation Guide

Brocade

®

G720 Switch Hardware Installation Guide

Attaching the Rear Brackets to the Extensions

Complete the following steps to attach the rear brackets to the extensions. You can use short or long rear brackets for this

task, depending on the depth of your rack.
1. Select the proper length rear bracket for your rack depth.
2. Slide the right rear bracket onto the right extension bracket, as shown in the figure.
3. Attach the brackets using four 6-32 x 1/4-in. panhead screws.

If possible, leave at least one empty vertical pair of holes between the screws for better support.

4. Repeat Step 2 and 3 to attach the left rear bracket to the left extension bracket.
5. Adjust the brackets to the rack depth and tighten all 6-32 x 1/4-in. screws to a torque of 10 cm-kg (9 in.-lb).

Figure 7: Attaching the Rear Brackets to the Extensions

1. Rear Brackets

2. Screws, 6-32 x 1/4-in. Panhead Phillips

G720-Install-IG101

26

Broadcom

«
...
24
25
26
27
28
...
»

Содержание Brocade G720























































































Отзывы:

Нет отзывов

Похожие инструкции для Brocade G720

Бренд: Hama Страницы: 9

IO-Link BNI LH1-303-S11-K091

Бренд: Balluff Страницы: 12

Edison Cooper Power Series

Бренд: Eaton Страницы: 12

Бренд: Black Box Страницы: 74

Бренд: Optex Страницы: 2

Бренд: Hall Research Technologies Страницы: 9

Бренд: Pakedge Device & Software Страницы: 14

Бренд: Pakedge Device & Software Страницы: 8

Бренд: Black Box Страницы: 2

Бренд: Pakedge Device & Software Страницы: 8

TMS 5XX SE AQ-EU Series

Бренд: Triax Страницы: 6

Бренд: Wave Italy Страницы: 32

Бренд: Hama Страницы: 12

24/48 10/100 Ports + 2GE

Бренд: Accton Technology Страницы: 512

Бренд: 3onedata Страницы: 2

True Scale Fabric 12000 Series

Бренд: Intel Страницы: 125

AMX DVX-2265-4K

Бренд: Harman Страницы: 2

Бренд: Raritan Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды