Broadcom Brocade G720 Скачать руководство пользователя страница 71

Страница: 71 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

LEDs

System Component

Description

System power LED

One green system power status LED (upper) on the port side.

System status LED

One bicolor (green/amber) system status LED (lower) on the port side.

Ethernet port speed LED

One status LED on the right of the RJ-45 connector. Glows green for 1000Mb/s and off for

100/10Mb/s.

Ethernet port activity LED

One link activity LED on the left of the RJ-45 connector.

FC port status LEDs

48 LEDs (green/amber) for the first 48 SFP+ ports and 8 tri-color LEDs (green/amber/white) for the

last 8 SFP+ ports 48, 50, 52, 54, 56, 58, 60, and 62. The last set of LEDs pulse once in white, before

indicating the FC port status in green or amber. All functionalities pertaining to the green/amber

colors for the last 8 LEDs remain the same as the first 48 LEDs.

Power supply and fan assembly

status LEDs

One green power-supply and fan-assembly status LED on each power supply and fan assembly on

the nonport side of the switch.

Cables, Connectors, and Adapters

System Component

Description

Serial cable

RJ-45 console cable.

RJ-45 to mini-USB adapter

RJ-45 to mini-USB for the console cable.

Mini-USB

USB socket for the serial port.

Weight and Physical Dimensions

Empty weight refers to the device with two power-supply and fan assemblies installed but no SFP+ or QSFP transceivers.

Model

Height

Width

Depth

Weight (Empty)

Weight (Fully

Loaded)

Brocade G720

Switch

4.39 cm

1.73 in.

44.00 cm

17.32 in.

35.56 cm

14.00 in.

7.05 kg

15.54 lb

8.08 kg

17.81 lb

Environmental Requirements

Condition

Operational

Nonoperational

Ambient temperature

0°C to 40°C (32°F to 104°F)

–25°C to 70°C (–13°F to 158°F)

Relative humidity

(noncondensing)

10% to 85% at 40°C (104°F)

10% to 90% noncondensing

Altitude (above sea level) 0m to 3000m (9842 feet)

0m to 12,000m (39,370 feet)

Shock

20.0G, 6 ms, half-sine wave

33.0G, 11 ms, half-sine wave, 3G axis

Vibration

0.25G sine, 0.4 grams random, 5–500 Hz

5 Hz at 0.5 grams, 10–500 Hz at 1.0 grams (sine

vibration); 3–500 Hz at 1.12 grams (random

vibration)

Airflow

Maximum: 170 cmh (100 cfm)

Nominal: 120 cmh (71 cfm)

N/A

Operating noise

Maximum: 65 dB

N/A

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды