Broadcom Brocade G720 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 86

background image

G720-Install-IG101 Installation Guide

Brocade

®

G720 Switch Hardware Installation Guide

connected to the fabric after it has been powered on and the default domain ID is already in use, the fabric segments.

To find the domain IDs that are currently in use, enter the

fabricShow

command on another switch in the fabric.

Perform the following steps to modify the domain ID:
a) Disable the switch by entering the

switchDisable

command.

b) Enter the

configure

command. The command prompts display sequentially; enter a new value or press

Enter

to accept each default value.

c) Enter

y

after the

Fabric param

prompt.

Fabric param (yes, y, no, n): [no] y

d) Enter a unique domain ID (such as the domain ID used by the previous switch, if still available).

Domain: (1..239) [1] 3

e) Complete the remaining prompts or press

Ctrl+D

to accept the remaining settings without completing all the

prompts.

f) Re-enable the switch by entering the

switchEnable

command.

Verifying Correct Operation

Perform the following steps to verify correct operation of the device:
1. Check the LEDs to verify that all components are functional.
2. Verify the correct operation of the device by entering the following commands from the workstation.

Command

Description

errDump

Displays any errors

fanShow

Displays fans status and information

historyShow

Displays the device history

psShow

Displays power supply status and information

switchShow

Displays switch status and information

tempShow

Displays temperature status and information

The

switchShow

command provides the following information about the device and ports status.

G720switch:admin> switchshow
switchName: E_146156_C5c_LS1
switchType: 181.0
switchState: Online
switchMode: Native
switchRole: Subordinate
switchDomain: 156
switchId: fffc9c
switchWwn: 10:00:d8:1f:cc:12:c0:cd
zoning: ON (fos6k)
switchBeacon: OFF
FC Router: OFF
Fabric Name: FID1
HIF Mode: OFF
Allow XISL Use: ON

G720-Install-IG101

51

Broadcom

«
...
49
50
51
52
53
...
»

Содержание Brocade G720























































































Отзывы:

Нет отзывов

Похожие инструкции для Brocade G720

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 2

WJSX150 - SWITCHER - ADDENDUM

Бренд: Panasonic Страницы: 48

Бренд: FAAC Страницы: 2

Бренд: S&C Страницы: 28

Бренд: S&C Страницы: 12

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 28

Бренд: S&C Страницы: 37

EOC Master CD7944N

Бренд: Data Страницы: 18

Бренд: Labgear Страницы: 4

ALTUSCN KH1508I

Бренд: ATEN Страницы: 173

Бренд: Crestron Страницы: 2

Бренд: Festo Страницы: 2

Бренд: Enttec Страницы: 22

Бренд: Maiwe Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды