Broadcom Brocade G720 Скачать руководство пользователя страница 48

Страница: 48 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Configuring the IP Address

You can configure the device with a static IP address, or you can use a Dynamic Host Configuration Protocol (DHCP)

server to set the IP address of the switch. DHCP is enabled by default. The device supports both IPv4 and IPv6

addresses.

Using DHCP to Set the IP Address

When using DHCP, the switch obtains its IP address, subnet mask, and default gateway address from the DHCP server.

The DHCP client can connect only to a DHCP server that is on the same subnet as the switch. If your DHCP server is not

on the same subnet as the switch, use a static IP address.

Setting a Static IP Address

To set a static IP address for the device, complete the following steps.
1. Log on to the device as admin.
2. Use the

ipaddrset

command to set the Ethernet IP address.

•

To use an IPv4 address, enter the IP address in dotted decimal notation as prompted.

Ethernet IP Address: [192.0.2.0]

•

To use an IPv6 address, enter the network information in colon-separated notation as prompted.

device:admin> ipaddrset -ipv6 --add 2001:db8:8:800:200C:417A/32
IP address is being changed...Done.

3. Complete the rest of the network information as prompted (IPv4 format shown).

Ethernet Subnetmask: [255.255.255.0]
Ethernet IP Address: [192.0.2.0]
Gateway IP Address: [192.0.2.1]

4. Enter

off

to disable DHCP when prompted.

DHCP [OFF]: off

Setting the Date and Time

The date and time settings are used for event logging, error detection, and troubleshooting. However, device operation

does not depend on the date and time; a device with incorrect date or time values still functions properly.
You can synchronize the local time of the principal or primary fabric configuration server (FCS) device to that of an

external Network Time Protocol (NTP) server.
Perform the following steps to set the date and time:
1. Log on to the device as admin.
2. Enter the

date

[

new-date

] command at the command line.

The

new-date

variable specifies the new date and time and is enclosed in double quotation marks. This variable

is optional; if omitted, the current date and time are displayed. The date and time are specified as a string in

mmddhhmmyy

format:

G720-Install-IG101

Broadcom

Содержание Brocade G720























































































Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды

Broadcom Brocade G720, Руководство по установке оборудования

Результаты поиска

Содержание Brocade G720

Отзывы:

Похожие инструкции для Brocade G720

Бренды по названию

Популярные бренды