Baxi PBS-i WH2 Series Скачать руководство пользователя страница 84

Страница: 84 / 180

6.3.2

Fitting the assembly rail

1. Drill 2 holes with a diameter of 10 mm.

Important

Extra holes are provided in case one or other of the standard

locating holes prevents the correct location of the plug.

2. Put the plugs in place.

3. Fix the mounting rail to the wall using the hexagonal head screws

provided for this purpose. Set the level using a spirit level.

6.3.3

Mounting the module on the wall

1. Position the indoor module above the mounting rail so that it rests

snugly against it.

2. Gently lower the indoor module.

6.4

Putting the outdoor unit in place

6.4.1

Allowing sufficient space for the outdoor unit

Minimum distances from the wall are necessary in order to guarantee

optimum performance.

Fig.29

Drilling and mounting the rail

MW-3001007-1

302

ø1

218

Fig.30

Assembling the module

MW-3000538-2

6 Installation

AWHP-2 PBS-i

7706696 - v04 - 11102018

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 84 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: