manualshive.com logo in svg

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 147 / 180

Поделиться
Скачать
Baxi PBS-i WH2 Series Скачать руководство пользователя страница 147

10.3.4  Cleaning the casing

1. Clean the outside of the appliance using a damp cloth and a mild 

detergent.

10.3.5  Draining the heating circuit

1. Connect a suitable hose (internal diameter: 8 mm) to the drain cock 

on the heating circuit. The accessories bag supplied with the 

appliance includes a hose.

2. Open the drain valve.

3. Await the complete drainage of the heating circuit.

10.4  Specific maintenance operations

10.4.1  Replacing the battery in the control panel

If the indoor module is switched off, the control panel battery takes over to 

keep the correct time.
The battery must be replaced when the time is no longer saved.

1. Remove the front panel by pulling firmly upwards.

2. Tilt the control panel support forwards. 

3. Insert a screwdriver in the notches to remove the HMI unit from its 

housing.

4. Remove the battery located in back plate of the control panel by 

pushing it gently forwards. 

5. Insert a new battery. 

Important

Battery type:

CR2032, 3V

Do not use rechargeable batteries.

Do not discard used batteries in the dustbin. Take them to an 

appropriate collection place.

6. Re-assemble everything.

Fig.116 Accessing the back of the control 

panel

MW-3000547-02

2

Fig.117 Remove the battery

MW-5000165-1

10 Maintenance

7706696 - v04 - 11102018

AWHP-2 PBS-i

99

Содержание PBS-i WH2 Series





















































































































































































Отзывы:

Нет отзывов