manualshive.com logo in svg

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 129 / 180

Поделиться
Скачать
Baxi PBS-i WH2 Series Скачать руководство пользователя страница 129

Tab.58 Calculating the threshold coefficient of performance
If the coefficient of performance of the heat pump is higher than the threshold coefficient of performance, the heat pump takes 

priority. Otherwise only the boiler back-up is enabled. The heat pump coefficient of performance depends on the outside 

temperature and the heating water set point temperature.

HP061 parame­

ter

Description

HP061 = 1

Optimisation of energy costs for the consumer (factory setting): the control system chooses the cheapest 

generator according to the coefficient of performance of the heat pump and according to energy cost.

The switch between the heat pump and the boiler occurs at the value of the threshold coefficient of per­

formance calculated according to energy cost optimisation mode with the energy cost parameters.

HP062: Peak rate cost of electricity
HP063: Off-peak rate cost of electricity
HP064: Cost of fossil energy (oil or gas) – price per m

3

 or per litre – Can be set from 0.01 to 2.50 €/kWh

:

HP061 = 2

Optimisation of primary energy consumption: The control system chooses the generator that consumes the 

least primary energy.

The switch between the heat pump and the boiler occurs at the HP054 threshold coefficient of performance 

value according to the primary energy consumption optimisation mode.

HP061 = 3

Optimisation of CO

2

 emissions: The control system chooses the generator that emits the least CO

2

.

The switch between the heat pump and the boiler occurs at the threshold coefficient of performance value 

calculated according to the CO

2

 emissions optimisation mode:

HP065: Electricity CO

2

 emissions in heating mode

HP066: Electricity CO

2

 emissions in domestic hot water production mode

HP067: Gas or oil CO

2

 emissions

HP061 = 0

No optimisation: The heat pump always starts up first, regardless of the conditions. The boiler back-up 

starts up afterwards, if necessary.

Influence of outdoor temperatures and bi-valency

C COP: Coefficient of performance

C

S

Threshold coefficient of performance

T Outdoor temperature

T

1

HP051 parameter: Minimum outdoor temperature for the heat 

pump to stop

T

2

HP000 parameter: Bi-valency outdoor temperature

9.3.9 

Configuring a convection fan or underfloor cooling

This function is only available when the type of circuit selected is 

underfloor heating or a convection fan: CP020 parameter set to 2 or 5.

Important

The heating should be activated in order for cooling to function.

1. Go to the Installer   menu.

2. Access the Installer menu by entering the code 0012 by pressing the 

 and   keys.

3. Confirm access by pressing the 

 key.

4. Access the EHC–04 PCB parameters by pressing the   or   key.

Fig.103

+

T

1

T

2

T

C

C

S

+

T

1

T

2

T

C

C

S

T

1

T

2

T

C

C

S

MW-5000542-1

9  Settings

7706696 - v04 - 11102018

AWHP-2 PBS-i

81

Содержание PBS-i WH2 Series





















































































































































































Отзывы:

Нет отзывов