Baxi PBS-i WH2 Series Скачать руководство пользователя страница 82

Страница: 82 / 180

6 Installation

6.1

Installation regulations

Warning

The components used for the connection to the cold water supply

must comply with the prevailing standards and regulations in the

country concerned.

Caution

Installation of the heat pump must be done by a qualified

professional in accordance with prevailing local and national

regulations.

6.1.1

Data plate

The data plates identify the product and provide the following important

information.
The data plates must be accessible at all times.

Important

Never remove or cover the data plates and labels affixed to the

heat pump.

The data plates and labels must be legible throughout the entire

lifetime of the heat pump. Immediately replace damaged or

illegible instructions and warning labels.

Data plate on the indoor module

Data plate on the outdoor unit

Fig.25

MW-3000537-01

Fig.26

MW-M001832-1

6 Installation

AWHP-2 PBS-i

7706696 - v04 - 11102018

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 82 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: