Baxi PBS-i WH2 Series Скачать руководство пользователя страница 128

Страница: 128 / 180

6. Configure the HP033 parameters according to the type of energy

meter installed. By default, the pulse weight is set to 1 Wh, the setting

range of the HP033 parameter goes from 0 (no metering) to 1000 Wh.

If the pulse weight is in kWh, use the following table.

Tab.56 If the pulse weight is given in kWh
Any numbers other than those stated in the table will not work.

Number of pulses per

kWh

Values to be configured for the HP033

parameter

1000

500

250

200

125

100

125

200

250

500

1000

7. Configure the HP034 and HP035 parameters.

Tab.57

Situation

Configuration

If a hydraulic back-up is

fitted

Set the HP034 and HP035 parameters to 0.

If an electrical back-up

is fitted

Set the HP034 and HP035 parameters according to the configuration of the electrical back-up stages

output.

9.3.7

Configuring a hydraulic back-up

Configure the back-up boiler according to its control panel. Set the installer

parameters.

1. Switch the boiler control system to 24h/24 comfort mode.

2. Heating set point temperature = Domestic hot water set point

tempe 5°C.

See

Boiler installation manual.

9.3.8

Configuring the hybrid operating mode of a hydraulic

back-up

Important

Hybrid operating mode is only available for appliances with a

hydraulic back-up.

The hybrid function consists of an automatic switch between the heat

pump and the boiler, according to the cost, the consumption or emission of

of each heat generator.

9 Settings

AWHP-2 PBS-i

7706696 - v04 - 11102018

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 128 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: