Baxi PBS-i WH2 Series Скачать руководство пользователя страница 107

Страница: 107 / 180

7.3

Commissioning procedure

Caution

Initial commissioning must be performed by a qualified

professional.

1. Refit all the panels, fascias and covers on the indoor module and

outdoor unit.

2. Arm the indoor module and outdoor unit circuit breakers on the

electric panel by setting them to the I position.

3. If necessary, arm the electrical back-up circuit breaker on the

distribution board by setting it to the I position.

The heat pump is switched on. When powering up for the first time,

the control panel displays the CNF menu which enables the type of

outdoor unit present in the installation to be set.

4. Set the CN1 and CN2 parameters according to the table below.

5. The heat pump begins the start-up cycle.

7.3.1

CNF Menu

The CNF menu is used to configure the hybrid heat pump according to the

type of back-up and the output of the outdoor unit installed.

Tab.41 Value of the CN1 and CN2 parameters with a hydraulic back-up

Output of the outdoor unit

CN1

CN2

4.5 kW

6 kW

8 kW

11 kW

16 kW

Tab.42 Value of the CN1 and CN2 parameters with an electrical back-

Output of the outdoor unit

CN1

CN2

4.5 kW

6 kW

8 kW

11 kW

16 kW

7.3.2

Start-up cycle

During the start-up cycle, the display shows various brief items of

information for checking.
These items of information are displayed one after the other.

1. Display of the control panel version

2. SCAN to search for the various options connected

Fig.62

-5

-3

Fig.63

-5

-3

7 Commissioning

7706696 - v04 - 11102018

AWHP-2 PBS-i

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 107 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: