Baxi PBS-i WH2 Series Скачать руководство пользователя страница 125

Страница: 125 / 180

5. Access the languages available by pressing the

key.

6. Select the language by pressing the or keys until the desired

language is displayed.

7. Confirm by pressing the

key.

8. Go back to the main display by pressing the

key.

9.3.2

Selecting the type of outdoor unit and the type of back-up

(CN1 et CN2)

1. Go to the Installer menu.
2. Access the Installer menu: enter the code 0012 by pressing the

and keys.

3. Confirm access by pressing the

key.

4. Access the EHC–04 PCB parameters by pressing the or key.
5. Select the CNF menu (control panel reset) by pressing the or

keys.

6. Confirm by pressing the

key.

7. Refer to the table below and enter the values corresponding to the

type of outdoor unit and the type of back-up by pressing on the or

keys.

8. Confirm the selection by pressing the

key.

9. Go back to the main display by pressing the

key.

CNF Menu

The CNF menu is used to configure the hybrid heat pump according to the

type of back-up and the output of the outdoor unit installed.

Tab.53 Value of the CN1 and CN2 parameters with a hydraulic back-up

Output of the outdoor unit

CN1

CN2

4.5 kW

6 kW

8 kW

11 kW

16 kW

Fig.98

-5

-2

Fig.99

-5

-2

Fig.100

-5

Fig.101

-6

-3

9 Settings

7706696 - v04 - 11102018

AWHP-2 PBS-i

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 125 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: