Baxi PBS-i WH2 Series Скачать руководство пользователя страница 109

Страница: 109 / 180

3. Select the number corresponding to the installation type by pressing

the or key. Selecting the installation type enables automatic

configuration of the parameters required for the control panel to

operate correctly (gradient, maximum circuit temperature, etc.). For a
configuration which differs from those proposed here, press the

key on the control panel and configure the parameters manually.

Installation type

No.

One direct heating circuit

One direct heating circuit and one domestic hot water

tank

One direct heating circuit and one underfloor heating cir

cuit with mixing valve

One direct heating circuit and one domestic hot water

tank and one underfloor heating circuit with mixing valve

One direct underfloor heating circuit

One direct underfloor heating circuit and one domestic

hot water tank

4. Confirm the selection by pressing the

key.

5. Set the heating curve.

The main parameters are set.

6. Apply the required settings based on the additional options connected.

7.5

Checking the minimum flow

Heating installations must be able to guarantee a minimum flow rate at all

times. If the flow rate is too low, the heat pump may shut itself down for its

own protection; the heating, cooling and domestic hot water functions are

then no longer guaranteed.

1. Check the minimum flow rate as defined by the HP010 parameter.

See

The flow rate value within the installation can be read using the

AM056 parameter.

2. Set the differential pressure valves to guarantee an optimum flow rate

in the installation when thermostatic valves are closed. The optimum

flow rate is defined by the HP069 parameter.

7.6

Final instructions for commissioning

1. If necessary, deactivate the heat pump's domestic hot water mode.

2. Simulate a heat demand to start up heating mode.

3. Check start-up of the outdoor unit and the back-ups connected.

4. Check the flow rate in the installation in comparison to the minimum

flow rate.

5. Put the heat pump in shut-down/frost protection mode.

6. After about 10 minutes, vent the air in the heating system.

7. Check the hydraulic pressure on the user interface. If necessary, top

up the water level in the heating system.

8. Check the fouling level of the filter(s) inside and outside the heat

pump. If necessary, clean the filter(s).

9. Restart the heat pump and deactivate shutdown/frost protection mode

Fig.69

-1

Fig.70

MW-10001142-2

19°

7 Commissioning

7706696 - v04 - 11102018

AWHP-2 PBS-i

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 109 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: