manualshive.com logo in svg

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 119 / 180

Поделиться
Скачать
Baxi PBS-i WH2 Series Скачать руководство пользователя страница 119

ADV

Description of the ADV advanced parameters

Factory setting

CIRCB

CP730

Selection of heat up speed of the zone

0 =Extra Slow

1 =Slowest

2 =Slower

3 =Normal

4 =Faster

5 =Fastest

Do not modify this setting

2

CP740

Selection of Cool down speed of the zone

0 =Slowest

1 =Slower

2 =Normal

3 =Faster

4 =Fastest

Do not modify this setting

2

CP770

The zone is after a Buffer tank

0 =No

1 =Yes

Do not modify this setting

1

9.2.3 

Installer  \DHW menu

A domestic hot water sensor must be connected to the EHC–04 board to 

display these parameters.
DP : Direct Hot Water Parameters = Domestic hot water tank parameters

Tab.47

Parameter

Description

Factory setting

DP051

Domestic Hot Water ECO or CONFORT setting

0 =ECO (Only HP)

1 =Comfort (HP+Boiler)

0

DP120

Hysteresis temperature relative to the DHW temperature setpoint

Can be set from 0 °C to 40 °C

8

DP130

Offset added on the DHW temperature to obtain the dynamic generator setpoint. 20

DP213

Post run time of the DHW pump/3 way valve after DHW production

Can be set from 0 Min to 99 Min

3

ADV

Advanced parametersADV

 

9.2.4 

Installer  \DHW\ADV menu

A domestic hot water sensor must be connected to the EHC–04 board to 

display these parameters.
DP : Direct Hot Water Parameters = Domestic hot water tank parameters

Tab.48 List of ADV parameters in the sub-menu of the Installer   menu

ADV

Description of the ADV advanced parameters

Factory setting

DP004

Legionella mode protection calorifier

0 =Disabled

1 = on: the domestic hot water tank is superheated to 65 °C for 20 minutes 

once a week.

2 = automatic: the domestic hot water tank is remotely controlled.

0

DP046

Maximum domestic hot water temperature

Can be set from 10 °C to 70 °C

70

9  Settings

7706696 - v04 - 11102018

AWHP-2 PBS-i

71

Содержание PBS-i WH2 Series





















































































































































































Отзывы:

Нет отзывов