Baxi PBS-i WH2 Series Скачать руководство пользователя страница 122

Страница: 122 / 180

Parameter

Description

Factory setting

EHC–04

Auto detect

available

CNF

Reset factory parameters

See the data plate.

ADV

ADV advanced parameters

not available

9.2.6

Installer \EHC–04 and SCB-04\ADV menu

AP : Appliance Parameters = Appliance parameters

ADV

Description of the ADV advanced parameters

Factory setting

EHC–04

Factory setting

SCB-04

AP002

Enable manual heat demand function

In this mode, the temperature set point used will be that for the

AP026 parameter.

AP006

Appliance will report low water pressure below this value

Can be set from 0 bar to 6 bar

0.3

not available

AP009

Number of heat generator operating hours for raising a service

notification

Can be set from 0 to 65534 hours

17400

not available

AP010

Service:

0 =None

1 =Custom notification

2 =ABC notification

not available

AP011

Hours powered to raise a service notification

Can be set from 0 to 65534 hours

17400

not available

AP026

Flow temperature setpoint for manual heat demand

Can be set from 7 to 80°C

Set point used when manual mode is active (AP002 = 1)

not available

AP058

Warning message indicating that pressure is low

Can be set from 0 bar to 2 bar

0.8

not available

AP072

Type of the humidity sensor used

0 =No

1 =OnOff

2 =0-10V sensor

AP101

Disable (0) or Enable (1) the de-aeration cycle

0 =Off

1 =Auto

2 =On

not available

AP102

Configuration of the boiler pump as zone pump or system pump

(feed lowloss header)

0 =No

1 =Yes

not available

HP : Heat-pump Parameters = Heat pump parameters

Tab.51

ADV parameter

Description of the ADV advanced parameters

Factory setting

EHC–04

HP002

Maximum flow temperature of the heat pump without backups

Can be set from 20 °C to 90 °C

65 (6 kW - 8 kW - 11

kW - 16 kW)

60 (4.5 kW)

HP003

Minimum flow temperature allowed in cooling mode

Can be set from 5 °C to 30 °C

9 Settings

AWHP-2 PBS-i

7706696 - v04 - 11102018

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 122 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: