Baxi PBS-i WH2 Series Скачать руководство пользователя страница 80

Страница: 80 / 180

1. Connect the accessories and options to the EHC–04 PCB, respecting

the 230-400 V and 0-40 V cable feed-throughs.

2. On initial start-up, or after a reset of the factory parameters, set the

CN1 and CN2 parameters according to the output of the outdoor unit.

3. Select the number corresponding to the installation type by pressing

the or key.

Installation type

No.

1 direct underfloor heating circuit

Selecting the installation type enables automatic configuration of the

parameters required for the control panel to operate correctly

(gradient, maximum circuit temperature, etc.).

4. Confirm the selection by pressing the

key.

The main parameters are set.

5. If necessary, configure the hybrid operating mode for the hydraulic

back-up

6. Setting up the back-up boiler

5.5

Connecting a swimming pool

The swimming pool is not heated when the contact is open (factory

setting). Only the frost protection continues to run.
The electrical connection for a swimming pool is made to the optional

SCB-04 PCB.

1. Connect the swimming pool secondary pump to the terminal block.

2. Connect the swimming pool temperature sensor to the TFlow terminal

block.

3. Connect the swimming pool primary pump to the

terminal block.

4. Connect the swimming pool heating cut-off control to the R-Bus

terminal block.

5.5.1

Configuring the heating of a swimming pool

Important

The SCB-04 optional PCB is required for controlling the

swimming pool heating.

To ensure the swimming pool heat pump operates correctly,

ensure a low-loss header is provided.

For the pool to be heated, a swimming pool thermostat is required.

The thermostat contact is open when the swimming pool temperature is

higher than the thermostat set point.

When the contact is closed, the swimming pool is heated.

1. Go to the Installer menu.

2. Access the Installer menu by entering the code 0012 by pressing the

and keys.

3. Confirm access by pressing the

key.

4. Access the circuit B and SCB-04 PCB parameters by pressing the

or key.

5. Confirm the selection by pressing the

key.

Fig.24

MW-6000381-6

5 Connecting diagrams and configuration

AWHP-2 PBS-i

7706696 - v04 - 11102018

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 80 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: