Baxi PBS-i WH2 Series Скачать руководство пользователя страница 153

Страница: 153 / 180

12 Decommissioning and disposal

12.1 Decommissioning procedure

To decommission the heat pump temporarily or permanently:

1. Switch off the heat pump.

2. Shut off the electrical power supply to the heat pump: outdoor unit and

indoor module.

3. Shut off the supply to the electrical back-up if an electrical back-up is

present.

4. Shut off the supply to the boiler if hydraulic back-up is present.

5. Drain the central heating system.

12.2 Disposal and recycling

Warning

Removal and disposal of the heat pump must be carried out by a

qualified professional in accordance with prevailing local and

national regulations.

1. Switch off the heat pump.

2. Cut the mains supply to the heat pump.

3. Recover the refrigerant fluid in accordance with prevailing regulations

Important

Do not allow the refrigerant fluid to escape into the atmosphere.

4. Disconnect the refrigerant connections.

5. Close the water mains.

6. Drain the installation.

7. Dismantle all hydraulic connections.

8. Dismantle the heat pump.

9. Scrap or recycle the heat pump in accordance with prevailing local

and national regulations.

Fig.125

MW-3000179-03

12 Decommissioning and disposal

7706696 - v04 - 11102018

AWHP-2 PBS-i

105

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 153 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: