Baxi PBS-i WH2 Series Скачать руководство пользователя страница 120

Страница: 120 / 180

ADV

Description of the ADV advanced parameters

Factory setting

DP047

Maximum time allowed to produce Domestic Hot Water

Can be set from 1 to 10 hours

3 (4.5 kW - 6 kW - 8

kW)

2 (11 kW - 16 kW)

DP048

Minimum heating time before Domestic Hot Water production

Can be set from 0 to 10 hours

DP055

Enable/disable the TAS protection of the DHW tankCan be set from 0 to 1

DP090

Delay for starting the next generator (backup stage) in DHW mode

Can be set from 0 Min to 120 Min

DP100

Delay for stopping the next generator (backup stage) in DHW mode

Can be set from 0 Min to 120 Min

DP110

Delay for starting the next generator (backup stage) in DHW mode

Can be set from 0 Min to 255 Min

DP150

Enable DHW Thermostat function

0 =Off

1 =On

DP160

Setpoint for DHW anti legionella

Can be set from 60 °C to 90 °C

Do not modify this setting

9.2.5

Installer \EHC–04 and SCB-04 menu

AP : Appliance Parameters = Appliance parameters

Tab.49

Parameter

Description

Factory setting

EHC–04

Factory setting

SCB-04

AP001

Blocking input setting (1: Full blocking, 2: Partial blocking, 3: User

reset locking) BL1:

1 = Full blocking of the installation – frost protection not guaran

teed

2 = Partial blocking of the installation – frost protection active

3 =User reset locking

4 =Backup Relieved

5 =Heat Pump Relieved

6 =HP & backup relieved

7 =High, Low Tariff

8 =Photovoltaic HP Only

9 =PV HP And backup

10 =Smart Grid ready

11= heating/cooling

not available

AP028

Defines the type of cooling used.

0 =Off

1 =Active cooling on

2 = Free cooling on, not used

AP063

Maximum central heating flow temperature setpoint

Can be set from 20 °C to 90 °C

Hydraulic back-

up: 90

Electrical back-

up: 75

not available

AP075

Outdoor temperature neutral band between heating and cooling. The

generator is stopped.

Can be set from 0 to 10 °C

AP079

Inertia of the building used for heat up speed

Can be set from 0 to 10

0 = 10 hours for a building with low thermal inertia,

= 22 hours for a building with normal thermal inertia,

10 = 50 hours for a building with high thermal inertia.

Modification of the factory setting is only useful in exceptional cases.

9 Settings

AWHP-2 PBS-i

7706696 - v04 - 11102018

Содержание PBS-i WH2 Series





















































































































































































Результаты поиска

Содержание PBS-i WH2 Series

Отзывы:

Baxi PBS-i WH2 Series, Руководство пользователя, Страница: 120 / 180

Результаты поиска

Содержание PBS-i WH2 Series

Отзывы: