ATS SuperTrak GEN3 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 366

ATS SuperTrak GEN3 Скачать руководство пользователя страница 38

26

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

SuperTrak Conveyance Platform Overview

Straight Section - Electrical Door Closed

ID

Component Name

Description

A

Electrical door (closed) Encloses the electrical components.

Straight sections are available with front mounted electronics
(FME) as shown, or rear mounted electronics (RME).

B

Linear motor

Produces the electromagnetic force that propels the pallets.
The linear motor includes:

• 20 potted coils.
• An iron core lamination assembly.

See

on page 39 for information about coil numbering.

C

Left encoder assembly

Measures the pallet position using encoder read heads.
See

Encoder Assemblies

on page 38 for information about

encoder numbering.

D

Right encoder
assembly

E

Upper v-rail

Provides a track for the pallet V-wheels to travel on.

F

Track structure

Aluminum structure that forms the base of a track. All other
track module components are mounted to the track structure.

G

Flat wear strip location Provides a smooth surface for the pallet flat wheels to travel

on.

H

Electrical interconnect

Connector for conduit that contains the power and network
cables.
See

Interconnect Kit (Straight Section to Straight Section)

I

Stand (1 of 2)

Mounts the section to the SuperTrak conveyance platform
frame.
Straight sections are available with standard-height stands as
shown, or low-profile stands.

«
...
36
37
38
39
40
...
»

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов