ATS SuperTrak GEN3 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 366

ATS SuperTrak GEN3 Скачать руководство пользователя страница 152

140

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Operating Procedures

TrakMaster Procedures

TrakMaster is a Windows-based application that monitors, configures, and is used
to troubleshoot the SuperTrak conveyance platform.

Download TrakMaster

1. Email

[email protected]

to obtain a login account.

2. Navigate to

http://atsautomation.leapfile.com/

.

3. Click

File Portal

.

4. Enter your

Login ID

and

Password

, and then click

Login

.

5. Click

SuperTrak G3

.

6. Complete one (1) of the following:

•

Select the checkbox(es) of
the required software
version, and then click

Download Selected

.

•

Click a folder to view the
folder contents, select the
checkbox(es) of the
required files, and then
click

Download

.

TrakMaster is not required to operate the SuperTrak conveyance
platform; however, it is useful for troubleshooting and configuring the
SuperTrak conveyance platform.

«
...
150
151
152
153
154
...
»

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов