manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 39 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 39

   SuperTrak Conveyance Platform Overview

SuperTrak™ GEN3 System Operation and Maintenance Manual

27

Rev. 9 (12-2021)

Straight Section - Electrical Door Open

•  The coil driver boards in the low power straight section are visually 

identical to the coil driver boards in the high power straight section, 
but they are different.

•  The left coil driver board and the right coil driver board are the same. 

The connections to the gateway boards are different, so they are 
referenced as the “left” or “right” coil driver board. 

ID

Assembly Name

Description

A

Electrical door (open)

Provides access to the straight section circuit boards.

B

Left coil driver board

See 

Straight Section - Left Coil Driver Board

 on page 

28, or 

Left Coil Driver Board with a Power Supply 

Connected

 on page 29.

C

Gateway board

See 

Gateway Board

 on page 30.

D

Right coil driver board

See 

Right Coil Driver Board

 on page 31.

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов