manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 204 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 204

192

 SuperTrak™ GEN3 System Operation and Maintenance Manual 

Rev. 9 (12-2021)

Technician Procedures

3. Install the pallet removal tool on the pallet:

a. Align the pallet removal tool 

holes with the pallet shoulder 
screws and then position the tool 
against the front of the pallet.

b. Slide the pallet removal tool to the left, to locate the shaft of the two 

(2) shoulder screws into the tool slots.

c. Rotate a locking finger over each 

of the two (2) shoulder screws.

4. Lift the pallet using the handles of the pallet removal tool. 

Make sure the encoder strip assembly is positioned at the top of the pallet.

5. Hold the pallet removal tool firmly. Rest 

the top left corner of the pallet on the 
upper v-rail of the SuperTrak conveyance 
platform, and then, align the anti-tip 
block of the pallet with the slot below the 
upper 

 

v-rail.

6. Hold the pallet level. With the anti-tip block in the left slot, rotate the pallet 

toward the motor until the anti-tip block on the right side moves into the slot 
below the upper v-rail.

Prevent strong impact of the pallet with the motor or damage could occur. 

7. Remove the pallet removal tool from the pallet.

8. Verify that a 0.5 mm (0.02 in.) gap exists between the pallet encoder strip 

assembly and the encoder assembly. 

See 

Adjust a Pallet Shim

 on page 207 for how to correctly measure or 

 

(if required) adjust the gap.

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов