manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 133 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 133

   Controls and Connections

SuperTrak™ GEN3 System Operation and Maintenance Manual

121

Rev. 9 (12-2021)

Ethernet POWERLINK Connection

The Ethernet POWERLINK connection exists in the control panel when it is shipped. 
One end of an Ethernet cable is plugged into the front port of Slot 2 on the 
controller, and the other end of the cable is plugged into IF1 of the bus controller, 
as illustrated:

ID

Connection 
Number

Connection Type Description

A

N/A

N/A

Ethernet POWERLINK connection location.

B

13K0:IF1/1

RJ45 POWERLINK 
connection

Connects to the controller (slot 2, front port).

C

14K3:1F1

RJ45 POWERLINK 
connection

Connects to the bus controller (upper port).

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов