ATS SuperTrak GEN3 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 366

ATS SuperTrak GEN3 Скачать руководство пользователя страница 16

4

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Preface

Referenced Terms

This section defines terms that are used throughout this document.

See

on page 277 for additional definitions.

Term

Description

SuperTrak conveyance
platform

Represents the SuperTrak™ GEN3.

TrakMaster

Represents the TrakMaster™ software.

Power supply

Represents the SuperTrak conveyance platform power supply.

Control panel

Represents the SuperTrak conveyance platform control panel.

Pallet

Represents the SuperTrak conveyance platform pallet.

User

Represents all levels of SuperTrak conveyance platform users. It
includes operators, maintenance personnel, and technicians.

Operator

Represents a user with basic mechanical knowledge.

Maintenance
Personnel

Represents a user with knowledge about routine cleaning, and
lubrication procedures. They are expected to complete adjustments
that are within validated ranges.

Technician

Represents a user that specializes in a discipline such as electrical,
mechanical, or programming. They are expected to complete
complex SuperTrak conveyance platform procedures; such as,
replacement procedures or adjustments that are outside of validated
ranges.

«
...
14
15
16
17
18
...
»

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов