manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 206 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 206

194

 SuperTrak™ GEN3 System Operation and Maintenance Manual 

Rev. 9 (12-2021)

Technician Procedures

3. Pry or tilt the pallet away from the 

motor: firmly hold both pallet removal 
tool handles, and then pull the right 
handle while resisting with the left 
handle

At approximately 15 degrees the 
magnetic pull decreases and the pallet 
can be removed from the motor. 

4. Slide a keeper plate over the pallet 

magnet assembly with the polycarbonate 
side of the keeper plate against the 
pallet magnet.

The keeper plate reduces the magnetic 
field produced by the magnet. The lexan 
creates a gap between the magnets and 
the steel plate. Hold the keeper plate in a 
manner that avoids fingers getting 
caught between the keeper plate and the magnets. 

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов