ATS SuperTrak GEN3 Скачать руководство пользователя страница 24

Страница: 24 / 366

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Safety Information

Lockout and Tagout Locations

The control panel is designed to be integrated with a main electrical panel that
includes a main power disconnect

switch.

To lock out SuperTrak conveyance platform hazardous energy, complete one (1) of
the following:

•

Lockout and tagout the

main power disconnect

switch when the SuperTrak

conveyance platform power must be OFF, but the SuperTrak conveyance
platform UPS power can be ON.

•

Lockout and tagout the

main power disconnect

switch and the

SuperTrak

conveyance platform power disconnect

switch when SuperTrak

conveyance platform power and UPS power must be OFF.

See

SuperTrak Conveyance Platform Power Disconnect Switch

on page 115,

SuperTrak Conveyance Platform Power ON Behavior

on page 137, and

SuperTrak

Conveyance Platform Power OFF Behavior

on page 139.

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 24 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: