ATS SuperTrak GEN3 Скачать руководство пользователя страница 225

Страница: 225 / 366

Technician Procedures

SuperTrak™ GEN3 System Operation and Maintenance Manual

213

Rev. 9 (12-2021)

4. Lift and remove the pallet encoder strip

assembly.

5. Obtain a replacement encoder assembly with a new encoder strip mounted.

Order this part from ATS.

6. Align the pallet encoder strip assembly that has a new encoder strip with the

pallet.

7. Secure the pallet encoder strip assembly in position with two (2) screws, two

(2) lock washers, and two (2) flat washers.

8. Align the pallet encoder strip assembly.

See

Adjust the Pallet Encoder Strip Assembly (Primary Encoder Strip)

page 226.

9. Install the pallet on the SuperTrak.

See

Install a Pallet

on page 191.

10. Verify that a 0.5 mm (0.02 in.) +/- 0.3 mm (0.01 in.) gap exists between the

pallet encoder strip assembly and the encoder assembly.

If the gap is less than 0.5 mm (0.02 in.) +/- 0.3 mm (0.01 in.), see

Adjust a

Pallet Shim

on page 207.

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 225 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: