ATS SuperTrak GEN3 Скачать руководство пользователя страница 187

Страница: 187 / 366

Technician Procedures

SuperTrak™ GEN3 System Operation and Maintenance Manual

175

Rev. 9 (12-2021)

5. Pull the 15A fuse straight out from the slot.

6. Install a new 15A fuse straight into the fuse slot.

Make sure the fuse is centered and seated correctly during installation.

7. If required, connect any coil connections that were disconnected in step 4.

Replace a Coil Fuse - 180 Deg. Section (500 mm)

1. Turn the

SuperTrak conveyance platform power disconnect switch

the OFF position.

2. Lock out and tag hazardous energy.

See

Lockout and Tagout Locations

on page 12.

3. Remove the top cover from the 180 deg. section.

4. Pull the 15A fuse straight out from the slot.

5. Install a new 15A fuse straight into the fuse slot.

Make sure the fuse is centered and seated correctly during installation.

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 187 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: