ATS SuperTrak GEN3 Скачать руководство пользователя страница 94

Страница: 94 / 366

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Installation

d. Repeat step a to c for the second cross-brace.

e. Secure the cross-brace in position

with four (4) screws.

f. Tap two (2) dowels halfway into

the cross-brace. Make sure the
dowel remains above the cross-
brace surface.

g. Repeat steps a to f for the second cross-brace.

2. Install the first straight section on the frame:

a. Lift and position a straight section

on the frame.

Roughly center the straight
section stands on the cross-
braces. Make sure the straight
section electrical box faces away
from the frame.

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 94 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: