ATS SuperTrak GEN3 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 366

ATS SuperTrak GEN3 Скачать руководство пользователя страница 113

Installation

SuperTrak™ GEN3 System Operation and Maintenance Manual

101

Rev. 9 (12-2021)

Install a Wedge Adjust - 180 Deg. (500 mm) Section

1. Verify that the edge of the wedge adjust

plate aligns with the center notch on the
side of the wedge adjust. If required, turn
the adjustment knob to obtain the correct
position.

Also make sure that the foam piece is
adhered to the wedge adjust as shown in
the photo.

2. Place the magnetic shunt into the opening

between the two (2) SuperTrak
conveyance platform sections.

(The magnetic shunt is an iron block that
improves the continuity of the magnetic
field for shuttle attraction. It has no
mechanical alignment purpose.)

Slide the magnetic shunt into the opening width-wise, and then push it
sideways into location. Do not place any objects in the opening before the
magnetic shunt is inserted. The magnetic shunt requires iron-to-iron contact
with the motor core of both the straight section and the 180 deg. section.

3. Align the wedge adjust across the straight

section and a 180 deg. section.

The end of the wedge adjust slides into
the opening that was used for the
magnetic shunt installation.

«
...
111
112
113
114
115
...
»

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов