ATS SuperTrak GEN3 Скачать руководство пользователя страница 75

Страница: 75 / 366

Installation

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

22. Align the lower flat rails with the adjustment features mounted below the E-

Turn plate.

See

Align a Flat Wear Strip

on page 241.

23. Repeat steps 16 to 22 for the second curved section.

24. Tighten the four (4) screws at the base of each straight section stand.

25. For 180 deg. (500 mm) sections only, reinstall the sections’ top covers, and

then reinstall the stand covers.

26. Install the lower flat wear strips.

See

Replace a Flat Wear Strip

on page 238.

27. Install the pallets.

See

Install a Pallet

on page 191.

28. If required, fine-adjust the upper v-rail.

See

Fine-Adjust the Upper V-Rail

on page 103.

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 75 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: