manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 361 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 361

   Appendix C: Component Data Sheets

SuperTrak™ GEN3 System Operation and Maintenance Manual

349

Rev. 9 (12-2021)

Interconnect Kit (Straight Section to Straight Section)

The interconnect kit provides all the necessary hardware to physically connect 

 

two (2) adjacent straight sections with FME mechanically, electrically, and 
functionally.

Features

The following items are included: 

Part Numbers

A

Flat rail

C

Straight-to-straight electrical interconnect

B

Wedge adjust

D

Ethernet network cable

a

Part

Part Number

Ethernet network cable

a

a. The Ethernet network cable is included with the straight-to-straight electrical interconnect, but 

 

    is also offered separately because it may be damaged during assembly or maintenance.

SP-3708400

Interconnect kit

4217881

Straight-to-straight electrical interconnect

SP-1060659

Wear strip

SP-1060669

Wedge adjust

SP-1060643

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов